|
1 BCI PO Box 470 Depew, NY 14043 TEL: 716-289-5532 FAX: 716-706-0233 E-MAIL: bakerschoiceinc@aol.com Patent Pending Technical Information Cure N Seal 15 Non-VOC, High Solids, Solvent Based, Non-Yellowing, Acrylic Concrete Curing, Sealing, and Dust proofing Compound. A Solvent Based Sealer with VOC's < 100 Grams/Liter Meets all State VOC (Volatile Organic Compound) Regulations (New Jan. 1, 2005 Regulations and Future Regulations coming into Law) Designed for use as a cure and seal (1 coat) on freshly placed concrete and as a 2 coat high gloss sealer for aged finished concrete. Use as a sealer/dustproof on both previously cured and new rough or smooth finished concrete surfaces. This curing/sealer contain 15% solids. Product Description •High Gloss •Repels Oil •Repels Grease •Repels Water •Will not stain Applied to freshly placed and finished concrete surfaces, CURE N SEAL 15 creates a vapor seal that retains moisture for proper curing. It also provides early rainfall protection and resistance to abrasion and staining. The sealer will protect against spalling, dusting, efflorescence, freeze thaw damage, and alkali degradation. CURE N SEAL 15 can also protect in food preparation areas from food and beverage stains and slabs in garages and parking facilities from grease and oil penetration Tarksone is the solvent used in CURE N SEAL 15. Tarksone is a 0 VOC solvent that evaporates very quickly and exhibits a flash point over 140 deg F. CURE N SEAL 15 is a 15% Acrylic exhibits UV resistance from sunlight, excellent protection against water and chloride intrusion. Unlike Epoxies, CURE N SEAL 15 L Acrylic will not yellow from UV exposure
Advantages •Specifically designed to meet the moisture retention properties of: ASTM C 1315 Type 1, Class A ASTM C 309 •Remains spray able in freezing temperatures •Ensures sufficient retention of mix water for at least 72 hours, allowing concrete to develop maximum strength, density and surface hardness •Prevents surface crazing and cracking •Dries to a dust and tack proof state in 30 minutes quickly providing protection from rainfall, scuffing and foot traffic •Acrylic Polymer – UV resistant, will not yellow •Reduces final clean-up costs by protecting concrete from oil, grease and chemical spills and from mortar splashing adhesion •Second applications, after finial clean up, beautify concrete appearance with a lustrous sheen and reduce after-occupancy maintenance costs •Treated surfaces are readily recoat able when necessary without sanding or scarification •CURE N SEAL 15; is compatible with most adhesives used for resilient floor coverings and concrete paints CURE N SEAL 15 HIGH GLOSS “WET LOOK” HIGH GLOSS FINISH
Physical Properties Boiling Point °F (Initial - Final) ------------------133°F (56°C) Specific Gravity (H2O = 1) -----------------------0.79 Solids------------------------------------------------ 15% Vapor Pressure (mm Hg@70°F) --------------186 Vapor Density (Air = 1) ---------------------------2 Evaporation Rate (Butyl Acetate = 100) ----14.5 Solubility in Water---------------------------------Not soluble Appearance-----------------------------------------Water White Colorless Liquid Odor---------------------------------------------------Ether/Acrylic Flash Point °F (PMCC.)------------------------147°F (64°C) Pensky Marten Closed Cup (Electronic Ignition) Percent Volatile----------------------------------77% VOC-------------------------------------------------90% is not a VOC under Federal & State Regulations. This product is a 10% VOC Use Instructions Site environmental conditions, substrate conditions and construction have a major effect on product selection, application methods, procedures and rates, appearance and performance. Product literature provides general information applicable to some or most conditions. However, an adequate site test application by the purchaser or installer in advance of field scale use is mandatory, to verify that product and quantities can be satisfactorily applied and will achieve desired appearance and performance under intended use conditions. Low pressure spray application, with proper nozzle, provides the best results, however, product can be applies with brushes or rollers. Spray apparatus should be equipped with chemically resistant hoses and gaskets. Larger areas are most economically treated with power sprayers. Do not thin or dilute
Applications Application rates vary with substrate conditions. Approximate rates for curing is 400 square feet per gallon Approximate rate for sealing is 400 - 500 square feet per gallon Application equipment should be cleaned with solvents
Freshly Placed Concrete Apply immediately following finial finish and disappearance of surface water sheen Apply to the point of saturation and appearance of continuous surface film Concrete should be damp but not wet. Avoid over application, puddles, and runs. For maximum sealing and dust proofing benefits, apply second coat of CURE N SEAL 15 after final clean up and concrete is dry.
Previously Cured Concrete Remove all dirt, oil, grease, paint or foreign cure residue. Clean with 10% caustic solution Rinse thoroughly with clean water and squeegee off excess water. Allow surface to dry 24-48 hours prior to first application. Use moisture meter or adequate material test to verify satisfactory adhesion and appearance. Apply second application in 24 hrs.
Maintenance Wipe up all chemical, solvent or petroleum spills as soon as possible Remove all dirt and debris by sweeping. Wash and buff periodically to help maintain surface luster. Clean damaged coating areas promptly and recoat.
US and other patents pending |